<listing id="fnxzn"></listing>

          <sub id="fnxzn"><span id="fnxzn"></span></sub>
            <track id="fnxzn"><video id="fnxzn"><span id="fnxzn"></span></video></track>

            <output id="fnxzn"><sub id="fnxzn"></sub></output>

            山東山汽工程機械(集團)有限公司
            熱線電話:400-879-1999 山汽官方微信
            鄭重聲明 購機 售后
            在線詢價
            熱線電話:400-879-1999
            您現在所在的位置: 首頁> 常見問題 >

            怎么解決全自動上料攪拌車熄火問題?

            所屬分類:常見問題 發布時間:2022-02-18 來源:http://www.aqtop.com 瀏覽量:18

            1、打開油箱開關,拆下輸油泵進油管,看油流情況,如果油流很快,說明正常,如果油流時斷時續查油路。
            1. Turn on the oil tank switch, remove the oil inlet pipe of the oil transfer pump and check the oil flow. If the oil flow is fast, it indicates that it is normal. If the oil flow is intermittent, check the oil circuit.
            2、確定油路通順,柴油機供給系統沒有空氣后,可拆開油泵蓋板,扳動操縱手柄,撥動油泵拉桿,看拉桿是否靈活和柱塞彈簧是否斷裂。在拉桿靈活和柱塞彈簧沒斷的情況下,可啟動柴油機中速運轉10分鐘,還有斷火現象時,可用一只銅榔頭輕輕敲擊輸油泵大螺帽,一邊敲一邊聽柴油機聲音,如果聲音不正常,說明輸油泵活塞和推桿發卡,進行修理或更換。低壓油流通順后,可用手壓泵排除油路中的空氣,打開泵頭放氣螺釘,直到沒有氣泡時,方可上緊放氣螺釘。
            2. After confirming that the oil circuit is smooth and there is no air in the diesel engine supply system, remove the oil pump cover plate, pull the operating handle and pull the oil pump pull rod to see whether the pull rod is flexible and whether the plunger spring is broken. When the pull rod is flexible and the plunger spring is not broken, the diesel engine can be started to run at a medium speed for 10 minutes. When there is a fire break phenomenon, a copper hammer can be used to gently tap the large nut of the oil transfer pump and listen to the sound of the diesel engine while tapping. If the sound is abnormal, it indicates that the piston and push rod of the oil transfer pump are stuck for repair or replacement. After the low-pressure oil flow is smooth, the air in the oil circuit can be discharged by hand pump, and the vent screw of the pump head can be opened until there are no bubbles, and then the vent screw can be tightened.
            3、低壓油流通順后,可用手壓泵排除油路中的空氣,打開泵頭放氣螺釘,直到沒有氣泡時,方可上緊放氣螺釘。
            3. After the low-pressure oil flow is smooth, the air in the oil circuit can be discharged by hand pump, and the vent screw of the pump head can be opened until there are no bubbles, and then the vent screw can be tightened.
            4、如不行則應考慮是油嘴不霧化,油泵柱塞彈簧和彈簧座斷裂,卡死不工作,或是柴油內有水。拆下油嘴總成檢查開啟壓力和霧化,如果油嘴總成正常,可讓用戶用干凈柴油裝入壺中用油路旁接法進行試驗。若還有斷火現象應考慮是發動機問題。
            4. If not, it should be considered that the nozzle is not atomized, the plunger spring and spring seat of the oil pump are broken, stuck and inoperative, or there is water in the diesel oil. Remove the oil nozzle assembly and check the opening pressure and atomization. If the oil nozzle assembly is normal, the user can put clean diesel into the pot and test it with the oil circuit side connection method. If there is still a fire break, it should be considered to be an engine problem.
            5、拆下噴油器總成,轉動曲軸數圈,即有水噴出,說明缸蓋,缸體有裂紋或砂眼,遇到這種情況時,可向用戶解釋或向柴油機公司反映。屬于發動機問題就不作敘述。
            5. Remove the fuel injector assembly and rotate the crankshaft for several turns, that is, water is ejected, which indicates that there are cracks or sand holes in the cylinder head and cylinder block. In case of this situation, you can explain to the user or report to the diesel engine company. If it is an engine problem, it will not be described.
            本文由全自動上料攪拌車為您提供,我們的網站是:http://www.aqtop.com/我們將以全心全意的熱情為您提供服務,歡迎您的訪問
            This article is provided for you by the automatic feeding mixer. Our website is: http://www.aqtop.com/ We will provide you with services with wholehearted enthusiasm. Welcome to visit
            熱門產品 / HOT PRODUCT

             

            首頁 產品 電話 置頂
            中文字幕无码在线观看一区2020

                <listing id="fnxzn"></listing>

                    <sub id="fnxzn"><span id="fnxzn"></span></sub>
                      <track id="fnxzn"><video id="fnxzn"><span id="fnxzn"></span></video></track>

                      <output id="fnxzn"><sub id="fnxzn"></sub></output>